Silverline Soldering Sponges 10pk (633932)

Product Information

If after cleaning on the sponge / brass shavings the tip is still not shiny then melt a small amount of solder onto it and clean again. The flux in the solder will help to clean the tip.

For best results, the tip of your soldering iron should be cleaned after each use with either a brass wire sponge or a wet cloth dipped in water-soluble flux cleaner. This will prevent oxidation buildup on the tip which can lead to poor heat transfer. Cleaning your soldering iron tips is an essential part of caring for your soldering equipment. Soldering iron tips work best when they’re clean, so you should make sure they are bright and shiny before, during and after you use them.

You can only compare up to four products at a time.

Keep the iron in place and touch the solder to the wire until it’s fully coated. Repeat this process on the other wire. Before you tin your tip, make sure it is clean and dry. Be careful not to put too much on; it only requires a thin layer of solder and the tip should still be shiny afterwards. You should repeat this process before and after each soldering session. If you are working for long periods of time, be sure to regularly tin your soldering iron tips as you go along. Always use tweezers and/or gloves to hold surfaces and components that are being (or have recently been!) soldered

There is an old debate about which one of these methods is better, and the choice often boils down to personal preference.Apply a small amount of the cleaning paste directly onto the soldering iron tip and then press it against a damp sponge or cloth to remove all residue from the surface of the tip. Now it’s time to show you how to solder wires together. For this process, it’s recommended to use helping hands or other type of clamp device. Brass sponge has the mentioned advantage of not adding thermal stress to the tip when it cools, so it supposedly gives longer tip life. Other than that, it is mostly useful when you work with larger tips and need to remove large amounts of solder from the tip. More advanced tip-cleaning kits can also leave you with a fine solder layer across the tip as part of the cleaning process, which helps to prevent tool oxidation over time and improves the longevity of replaceable tips Due to the low temperatures used in soft soldering, it thermally stresses components the least, but does not create strong joints and is therefore unsuitable for mechanical load-bearing applications. #2 Hard or Silver Soldering (above 450 °C)

This section will explain the tools of the trade. Some of these you will need, some of these you will not. The first (and most common) apparatus is the simple yellow sponge.

50 Comments

It employs solder which is metal at higher temperatures and is stronger than those used in soft soldering. Silver soldering is a hard soldering method, and silver mixed with tin is utilized as a solder.

Before you can start soldering, you need to prep your soldering iron by tinning the tip with solder. This process will help improve the heat transfer from the iron to the item you’re soldering. Tinning will also help to protect the tip and reduce wear. Sometimes a pad might get damaged on your board. We show you how to fix it in this simple to follow guide. Yes, you can use rubbing alcohol to clean a soldering iron. It’s important to remember to unplug the iron and let it cool before cleaning. You should also avoid using any abrasive materials when cleaning with alcohol. Wipe the iron down with a cloth soaked in rubbing alcohol and then dry it off with a clean cloth. Do you need to clean helping hands after soldering? A proper solder joint is smooth, shiny and looks like a volcano or cone shape. You want just enough solder to cover the entire joint but not too much so it becomes a ball or spills to a nearby lead or joint.Soldering iron tip cleaning paste is an essential tool for any electronics technician. This special paste is designed to keep your soldering iron tip clean and free of contaminants that can cause short circuits or poor electrical connections. Using the correct soldering iron tip cleaning procedure will ensure your electronics projects are successful and safe. The CLMB will automatically clean the tip in just one second. A photoelectric sensor detects the tip when you introduce it into the opening and then activates the brushes. With the CLMS model, the brushes will run in either a continuous mode or when you press the button on the lower side of the opening.