If you need to drill through tiles, apply some masking tape to the tile to stop the drill bit from slipping

Water and waste pipes are an inevitable, and essential, part of your bathroom. But, for many people, they are unsightly and can ruin the overall look and feel of your carefully designed bathroom. When applying silicone sealant, fill the bath with water as this will ensure the sealant doesn’t pull away from the tiles when the bath is used If you don’t want to do this yourself, then you’ll need to hire a builder to construct the wall, and then a plumber to move the toilet or sink so that they fit neatly onto the new wall. If you also want to install lighting on your wall then you will need to hire an electrician too (but remember that electricians need special qualifications to carry out work in bathrooms). Alternatively, sign-up to our newsletter for the latest offers, newest product launches and advice. Got pipes running up the walls of your bathroom? Don’t worry. If you can’t box up your pipework, then another option is to build a fake wall. This option is ideal for larger, older properties where space isn’t an issue.Consider using a drain snake. These rods can be lowered into your drain and wiggled around to break up debris. Precisely follow all directions on a drain cleaner's label. Be sure the room is well-ventilated. Do not leave the drain cleaner inside the drain for longer than stated in the instructions. Locate the sealing rings for the bath waste and overflow plates. Then, attach them to the bath drain and overflow hole opening with sealant or plumber’s gold and wipe any access with a wonder wipe. You can now fix the bath and overflow waste to the bath drain holes. Step 6: Attach the bath waste

In an unvented hot water system cold water from the rising main supplies a cylinder. The cylinder is designed to cope with mains pressure water and the water is heated via an immersion heater or heating coil. If the cold taps are fed from the rising main, a cold water tank in the loft isn’t required. The flow rate and pressure of the water should be high. The standard bath waste hole is 40 mm (1&1/12 inch). Additionally, a typical trap and waste pipe leading out of the bath is also 40mm (1&1/12 inch). Conclusion: Bath wastes at Build & Plumb There are a multitude of ways to banish bad odours from our drains, many using simple household items. Wondering how to get rid of drain smell? We will look into the different methods later, but the below items are excellent solutions if you’re wondering how to get rid of smelly drains:

If you really, really want to hide the plumbing in your bathroom, you could change your bathroom furniture to versions which keep the water and waste pipes out of sight. If you’re short on time and don’t have a plunger or a drain snake handy, then try these natural remedies: Method one: Vinegar and baking soda If you are going to go down the route of creating a fake wall to hide your bathroom pipework, then make sure you get several quotes for having the work done and weigh up this option against the other options in this article before deciding to go ahead. There are several different methods of venting: wet venting, common venting, circuit venting, island fixture venting, etc…

If you haven’t got the budget to replace all of your bathroom furnishings with items that conceal their pipework, then a cheaper way of hiding your pipework is to box it in. To finish fitting the bath waste, you need to attach the bath waste to a waste trap and the wastewater pipe underneath the bath. You can either use push-fit pipes or solvent and solvent-weld pipes. Just consider the application before using this product to clear up any old drain issue. "This one is an oxidizing cleaner, so it's very tough on organic matter like hair and food, but less so on grease," says Rachel Rothman, chief technologist of the Good Housekeeping Institute. Once the water is at the right height, plunge the drain for around half a minute. Try a few times until the water starts to flow freely again. If you are planning to install an over bath shower, then choose a bath with a flat rim so a shower screen can create a watertight sealThis guide will explain everything you need to know to fit a bath waste for a new bath and how to replace an old one, including what tools you need, how to fit a pop-up bath waste, and more. Table of contents Locate the overflow rose and bath waste cover and attach them on the front of the bath to the bath waste using a screw and screwdriver. Baking soda: Let the hot tap run for a few seconds, making sure the water is hot. Next, pour one cup of baking soda then two cups of hot vinegar down the drain. Rinse with hot water an hour later. The ‘boxing in’ approach is ideal where you have pipes running along the floor at a low level. The box you create can then act as either an enhanced skirting board or a low shelf (depending on the height of the pipework). Once you’ve painted this box to match your walls, it’ll be barely noticeable. Alternatively, you may have a system where hot water is created instantaneously by a combination boiler and there is neither a cistern in the loft nor hot water cylinder for storage. The pressure of the water is high because the system is mains fed.