Windscreen Wiper Linkage Push Rod Arms Repair

£9.9
FREE Shipping

Windscreen Wiper Linkage Push Rod Arms Repair

Windscreen Wiper Linkage Push Rod Arms Repair

RRP: £99
Price: £9.9
£9.9 FREE Shipping

In stock

We accept the following payment methods

Description

Rarity:The new wiper linkage comes with new mounting rubbers and new wiper spindle seals, but no wiper arm securing nuts so the originals need to be saved. No you shouldn’t drive with a bad wiper linkage. Driving with faulty wipers isn't just potentially dangerous, it's also illegal and could result in a hefty fine if you’re pulled over. The wiper linkage is what attaches the windscreen wiper motor to the wiper arms and blades. How does the windscreen wiper linkage work and what are the components? Changing a wiper linkage is a routine repair for all mechanics and can be done both kerbside as well as in the workshop, providing it is safe to do so. Well worn:The main problem was that the two joints attaching the operating rods to the wiper spindles had all but fallen apart with wear – there should be minimal play.

Easy to break:Six plastic clips secure the intake moulding. Two fine screwdrivers are used to lift the inner pin slightly, allowing the whole clip to be removed.Cleaning up:The remnants of the old hinge covers are lifted off and the underside of the moulding cleaned smooth, and debris removed from the holes.

If it's possible to free wiper arm shafts out of the linkage, your mechanic may suggest an option to clean and lubricate the shafts without replacing parts. It is cheaper, but the proper solution is to replace the linkage. This means, if you have to pay for wiper motor repairs, keep the receipt. If there is a recall, you can apply for reimbursement. Initial assessment pointed to a serious engine cooling problem, but that was easily fixed. Then there have been leaking fuel pipes, a leaky injector seal, inoperative handbrake, new camshaft and fuel pump drive belts, new differential mountings and a professional interior clean to add to the bill. But we’re still comfortably within budget, including the parts for these jobs... The multimeter shows 12.38 Volt, but the motor doesn't run. This means the wiper motor is bad and needs to be replaced.

New Customers

Fully functioning wipers are a key safety feature in your car so it’s vital that you get them fixed as soon as you notice a problem. What are the signs of a bad wiper linkage? Botched:When buying this car, I’d noticed this overlong stud poking out of the scuttle, but was too busy assessing the rest of the car to investigate then.

Evidence:Although these two inner joints (left) attaching the rods to the motor’s crank arm were okay, the nearby gouge showed the linkage had been rubbing against the bulkhead. Electrics:With the moulding clear, the wiper motor’s electrical plug is disconnected by pressing the release tab, then the harness is moved safely out of the scuttle. Stop the rust:Each air intakegrille on the underside of the moulding is supported by a steel frame, so it’s worth applying a liquid grease to stop them rusting away.Push fit:Fitting the new covers is initially a matter of engaging the rubber pegs with the holes and then squeezing them gently in from the upper side, here. Mitsubishi recalled the 2007-2013 Outlander for wiper motor failures (recall SR-17-003). Another Mitsubishi recall (SR-16-010) covers a wiper motor in the 2011−2015 Outlander Sport / RVR. The windshield wiper linkage is designed to last the lifetime of the vehicle, but like any other mechanical part it can break or malfunction when you least expect it. As soon as you begin to notice your wipers struggling to move across the windscreen, making strange noises or moving out of sync, you should have your wiper system, including the linkage, looked at by a mechanic and replaced.

Final job:On the outside of each hinge cover are two rubber tongues that need to be carefully pressed downward to locate underneath the edge of the wing panel. Working windshield wipers are important for safe driving. Several manufacturers have issued recalls related to the wiper system and possibly more recalls will come in the future. Wobbly:The rogue stud (with five nuts) was there to support the wiper motor. In reality, the motor plate was holding the stud in place – all very wobbly. Rubber pegs:The hinge covers are fixed to the intake moulding by rubber pegs through these holes. The pegs can be sliced off from the underside using a craft knife. The cost of a wiper linkage replacement depends on your car and what parts your car's manufacturer recommends.The wiper linkage is the component that attaches the windscreen wiper motor to the wiper arms and blades. Its job is to transmit the motion of the wiper motor to the wiper arms and blades to clear rain, snow and ice from your windscreen. This component is an important safety feature as it plays a key role in ensuring the driver has good visibility at all times. How often should a wiper linkage need replacing? How it works:Lifting that inner pin of the clip allows the three lower legs to fold in so the clip can be pulled out. Squeeze legs in when refitting later.



  • Fruugo ID: 258392218-563234582
  • EAN: 764486781913
  • Sold by: Fruugo

Delivery & Returns

Fruugo

Address: UK
All products: Visit Fruugo Shop